UC250-F77-IU-IO-2M

Ultrasonic sensor. Single head system, IO-Link interface for parameterization, Programmable via DTM with PACTWARE, Selectable sound lobe width, Series: -F77, Operating voltage: 18 ... 30 V DC , ripple...

Ultrasonic sensor. Single head system, IO-Link interface for parameterization, Programmable via DTM with PACTWARE, Selectable sound lobe width, Series: -F77, Operating voltage: 18 ... 30 V DC , ripple 10 %_SS <br>, Interface type: IO-Link (available after activation via programming button until next reset), Output type: 1 analog output 0 (4) ... 20 mA or <BR>1 analog output 0 ... 10 V, UL approval: cULus Listed, Class 2 Power Source. Sensing range: 20 ... 250 mm. Adjustment range: 25 ... 250 mm. Dead band: 0 ... 20 mm. Standard target plate: 10 mm x 10 mm. Transducer frequency: approx. 400 kHz. Response delay: minimum : 8 ms factory setting: 29 ms. Sensor cycle time: ≥ 8 ms (factory setting) ; programmable to 60 s. Non-volatile memory: EEPROM. Write cycles: 300000. LED green: solid: power onflashing: standby mode or IO-Link communication. LED yellow: solid: object in evaluation rangeflashing: programming of the limits, object detected. LED red: solid: faultflashing: programming limits, object not detected. Operating voltage: 18 ... 30 V DC , ripple 10 %SS. No-load supply current: ≤ 50 mA. Power consumption: ≤ 500 mW. Time delay before availability: ≤ 300 ms. Interface type: IO-Link (available after activation via programming button until next reset). Input/output type: 1 synchronization connection, bidirectional. 0 Level0 ... 1 V1 Level2.5 V ... UBInput impedance> 22 kΩOutput currentcurrent source < 2.5 mAPulse length≥ 1 ms with external control, low active: . 0 Level: 0 ... 1 V. 1 Level: 2.5 V ... UB. Input impedance: > 22 kΩ. Output current: current source < 2.5 mA. Pulse length: ≥ 1 ms with external control, low active. Synchronization frequency: . Common mode operation≤ 141 HzMultiplex operation≤ 141 Hz / n , n = number of sensors , n ≤ 10: . Common mode operation: ≤ 141 Hz. Multiplex operation: ≤ 141 Hz / n , n = number of sensors , n ≤ 10. Output type: 1 analog output 0 (4) ... 20 mA or 1 analog output 0 ... 10 V. Resolution: current output: evaluation range [mm]/3200 but ≥ 0.35 mmvoltage output: evaluation range [mm]/4000 but ≥ 0.35 mm. Deviation of the characteristic curve: ≤ ± 1 % of full-scale value. Repeat accuracy: ≤ ± 0.1 % of full-scale value. Load impedance: current output: ≤ 500 Ohm voltage output: ≥ 1000 Ohm. Temperature influence: ≤ ± 0.75 % of the end value (with temperature compensation) from 10 minutes after switching on the sensor ; 0.17 %/K (without temperature compensation). Standard conformity: . StandardsEN IEC 60947-5-2:2020 IEC 60947-5-2:2019 EN 60947-5-7:2003 IEC 60947-5-7:2003 IEC 61131-9:2013: . Standards: EN IEC 60947-5-2:2020 IEC 60947-5-2:2019 EN 60947-5-7:2003 IEC 60947-5-7:2003 IEC 61131-9:2013. UL approval: cULus Listed, Class 2 Power Source. CCC approval: CCC approval / marking not required for products rated ≤36 V. Ambient temperature: current output -25 ... 60 °C (-13 ... 140 °F) voltage output -25 ... 70 °C (-13 ... 158 °F). Storage temperature: -40 ... 85 °C (-40 ... 185 °F). Connection type: cable PUR , 2 m. Core cross section: 4 x 0.19 mm2. Degree of protection: IP67. Material: . HousingPolycarbonateTransducerepoxy resin/hollow glass sphere mixture; polyurethane foam: . Housing: Polycarbonate. Transducer: epoxy resin/hollow glass sphere mixture; polyurethane foam. Installation position: any position. Mass: 51 g. Tightening torque, fastening screws: max. 0.2 Nm. Dimensions: . Height31 mmWidth12 mmLength23 mm: . Height: 31 mm. Width: 12 mm. Length: 23 mm. Output: near limit: 25 mm far limit: 250 mm Output mode: rising ramp output type: 4 ... 20 mA. Beam width: wide

Brand	Pepperl Fuchs
Lifecycle status	active