Pepperl Fuchs

VBA-4E3A-KE-ZE/R

AS-Interface sensor/actuator module. KE switch cabinet module, 4 inputs (PNP) and 3 relay outputs. Node type: A/B node. AS-Interface specification: V2.1. Required gateway specification: ≥ V2.1. Profile: S-7.A.0. IO code7ID codeAID1 code7ID2 code0: . IO code: 7. ID code: A. ID1 code: 7. ID2 code: 0. UL File Number: E106378. LED FAULT: Fault display; Red LEDred: Communication fault or address is 0red, flashing: Overload, internal input supply. LED INT: Internal input supply active; LED green. LED PWR: AS-Interface voltage; LED green. LED IN: switching state (input); 4 LED yellow. LED OUT: Switching state (output); 3 LED yellow. Auxiliary voltage (input): 12 ... 30 V DC PELV. Rated operating voltage: 26.5 ... 31.6 V from AS-Interface. Rated operating current: ≤ 35 mA (without sensors) / max. 235 mA. Surge protection: O1 ... O3: Over voltage category IIUEXT, Ue: Over voltage category III, safe isolated power supplies (PELV). Number/Type: 4 inputs for 2- or 3-wire sensors (PNP), DC. Supply: from AS-Interface (switch position INT, default settings) or external UEXT (switch position EXT). Voltage: 21 ... 31 V DC (INT). Current loading capacity: ≤ 150 mA, overload- and short-circuit protected (INT). Input current: ≤ 8 mA (limited internally). Switching point: according to DIN EN 61131-2 (Type 2). 0 (unattenuated)≤ 2 mA1 (attenuated)≥ 4 mA: . 0 (unattenuated): ≤ 2 mA. 1 (attenuated): ≥ 4 mA. Signal delay: < 2 ms (input/AS-Interface). Signal frequency: ≤ 250 Hz. Number/Type: 3 relay outputs, normally open. Supply: none. Nominal load: . Per contactmax. 2 A / 30 V DC; 2 A / 250 V ACPer module6 A: . Per contact: max. 2 A / 30 V DC; 2 A / 250 V AC. Per module: 6 A. Minimum load: . Per contact10 mA / 5 V DC: . Per contact: 10 mA / 5 V DC. Short-circuit-proof: Contact: 500 A / 40 ms. Switching off power: 500 VA. Switching delay: < 10 ms (AS-Interface/contact). Usage category: DC-13 and AC-14. Switching frequency: < 20 Hz (without load)< 0.1 Hz (nominal load). Switching: . Mechanical30 x 106Electrical1 x 106 switching cycles (40 V DC, 2 A, ohmic)0.5 x 106 switching cycles (253 V AC, 2 A, cos φ = 1)0.45 x 106 switching cycles (253 V AC, 2 A, cos φ = 0.7): . Mechanical: 30 x 106. Electrical: 1 x 106 switching cycles (40 V DC, 2 A, ohmic)0.5 x 106 switching cycles (253 V AC, 2 A, cos φ = 1)0.45 x 106 switching cycles (253 V AC, 2 A, cos φ = 0.7). Input/Output: IN1 ... IN4 to O1 ... O3: safe isolation acc. to EN 60947-1,rated insulation voltage 278 V AC. Input/AS-Interface: none. Output/Output: O1 to O2, O3: safe isolation according to EN 60947-1,rated insulation voltage 278 V ACO2 to O3: basic insulation according to EN 60947-1,rated insulation voltage 278 V AC. Output/AS-Interface: safe isolation acc. to EN 60947-1,rated insulation voltage 278 V AC. Electromagnetic compatibility: . Directive 2014/30/EUEN 62026-2:2013 EN 61000-6-2:2005, EN 61000-6-4:2007: . Directive 2014/30/EU: EN 62026-2:2013 EN 61000-6-2:2005, EN 61000-6-4:2007. Low voltage: . Directive 73/23/EECEN 60947-1:2007: . Directive 73/23/EEC: EN 60947-1:2007. Galvanic isolation: EN 60947-1. Electromagnetic compatibility: NAMUR NE 21: 1998-08. Degree of protection: EN 60529:2000. Pollution degree: EN 60947-5-1. Input: EN 61131-2:2004. Usage category: EN 60947-5-1. Emitted interference: EN 61000-6-4:2007. AS-Interface: EN 62026-2:2013. Noise immunity: EN 61000-6-2:2005. Ambient temperature: -25 ... 60 °C (-13 ... 140 °F). Storage temperature: -25 ... 85 °C (-13 ... 185 °F). Relative humidity: 85 % , noncondensing. Climatic conditions: For indoor use only. Altitude: ≤ 2000 m above MSL. Pollution degree: 2. Degree of protection: IP20. Connection: removable terminalsrated connection capacity:rigid/flexible (with and without wire-end ferrules): 0.25 mm2 ... 2.5 mm2for multiple-wire connection with two wires of equal cross-section:flexible with twin wire-end ferrules: 0.5 mm2 ... 1.5 mm2. Material: . HousingPA 66-FR: . Housing: PA 66-FR. Mass: 170 g. Dimensions: . Height99 mmWidth22.5 mmLength102 mm: . Height: 99 mm. Width: 22.5 mm. Length: 102 mm. Mounting: DIN mounting rail. Tightening torque of clamping screws: 0.5 Nm ... 0.6 Nm

Brand	Pepperl Fuchs
Lifecycle status	active

Not currently in stock

Price on request

Request sourcing Ask a question